Microsoft word - msds306.doc

MSDS No.: 306
Revision No.:
Revision Date: 07/10/08
MATERIAL SAFETY DATA SHEET
Product name:
HIT- HY150 MAX
Description:
Methacrylate resin and hardener. Part A is in the large tube; Part B is in the small tube. Supplier:
Hilti, Inc. P.O. Box 21148, Tulsa, OK 74121 Emergency # (Chem-Trec.):
1 800 424 9300 (USA, PR, Virgin Islands, Canada); 001 703 527 3887 (other countries) INGREDIENTS AND EXPOSURE LIMITS
Ingredients:
CAS Number:
Part B: Quartz
Abbreviations: NJ TSRN indicates New Jersey Trade Secret Registry Number. (R) indicates “as respirable dust”. (N) indicates “as
nuisance dust”. PEL = OSHA Permissible Exposure Limit. TLV = ACGIH Threshold Limit Value. STEL = Short Term Exposure
Limit (15 minute time-weighted average). NE = None Established. mppcf = million particles per cubic foot. (M) = Mist
PHYSICAL DATA
Appearance and Odor:
VOC Content:
Boiling Point:
Vapor Pressure (@68 º F)
Vapor Density: (air = 1)
Odor Threshold
Evaporation Rate:
Solubility in Water:
Specific Gravity:
FIRE AND EXPLOSION HAZARD DATA
Flash Point:
Flammable Limits:
Extinguishing Media:
Special Fire Fighting
Use a self-contained breathing apparatus when fighting fires involving chemicals. Procedures:
Unusual Fire and Explosion
None known. Thermal decomposition products can be formed. Hazards:
REACTIVITY DATA
Stability:
Dibenzoyl peroxide decomposes (non-violently) at 150º F. Ignition does not occur due to the water content (> 5%). Hazardous Polymerization:
Incompatibility:
Strong acids and oxidizing agents. Do not store in direct sunlight. Decomposition Products:
Thermal decomposition can yield CO, CO2 and NOx. Conditions to Avoid:
Avoid temperature extremes which could shorten the shelf-life of this product; i.e. below 41º F freezing and above 77º F. (See handling and storage requirements). HEALTH HAZARD DATA
Known Hazards:
Eye and skin irritation. Possible sensitizer. Signs and Symptoms of
Eyes: can cause irritation. Skin: Prolonged and repeated contact can cause irritation. An
HILTI ® is a registered trademark of Hilti Corp. Exposure:
allergic skin reaction (sensitization e.g. rash, itching, reddening) can occur with some individuals.
Inhalation: Possible irritation. Ingestion: Not a likely route of exposure.
Routes of Exposure:
Carcinogenicity:
IARC classifies crystalline silica (quartz sand) as a Gp I carcinogen based upon evidence among workers in industries where there has been long-term and chronic exposure (via inhalation) to silica dust; e.g. mining, quarry, stone crushing, refractory brick and pottery workers. This product does not pose a dust hazard; therefore, this classification is not relevant. Medical Conditions
Aggravated by Exposure:
EMERGENCY AND FIRST AID PROCEDURES
Flush with plenty of water. Contact a physician if symptoms occur. Inhalation:
Move victim to fresh air. Call a physician if symptoms persist. Ingestion:
Contact a physician immediately. Do not induce vomiting unless directed by a physician. Referral to a physician is recommended if there is any question about the seriousness of the injury/exposure. CONTROL MEASURES AND PERSONAL PROTECTIVE EQUIPMENT
Ventilation:
General (natural or mechanically induced fresh air movements). Eye Protection:
Skin Protection:
Respiratory Protection:
None normally required. Where ventilation is inadequate to control vapors, use a NIOSH-approved respirator with organic vapor cartridges. Never enter a confined space without an appropriate air supplied respirator. If dusts are generated during demolition or removal, wear an appropriate dust mask or respirator. PRECAUTIONS FOR SAFE HANDLING AND USE
Handling and Storing
Store in a cool, dry area preferably between 41º and 77º F. Do not store in direct sunlight. Keep Precautions:
away from open flames, heat sources and sparks. Avoid prolonged or repeated contact. Use with adequate ventilation. Always wash thoroughly after handling chemical products. For industrial use only. Keep out of reach of children. Spill Procedures:
Take up with an absorbent material and place in a container for proper disposal. REGULATORY INFORMATION
Hazard Communication:
This MSDS has been prepared in accordance with the federal OSHA Hazard Communication Standard. 29 CFR 1910.1200. HMIS Codes:
Health 1, Flammability 1, Reactivity 0, PPE B DOT Shipping Name:
IATA / ICAO Shipping Name:
TSCA Inventory Status:
Urethane methacrylate resin – USEPA Accession Number 238392. All other chemical components listed on TSCA inventory. SARA Title III, Section 313:
This product contains 5 - 10% Benzoyl peroxide (CAS #94-36-0) which is subject to reporting under Section 313 of SARA Title III (40 CFR Part 372). EPA Waste Code(s):
Not regulated by EPA as a hazardous waste Waste Disposal Methods:
Consult with regulatory agencies or your corporate personnel for disposal methods that comply with local, state, and federal safety, health and environmental regulations. CONTACTS
Customer Service:
Technical Service:
Health / Safety:
Emergency # (Chem-Trec):
1 800 424 9300 (USA, PR, Virgin Islands, Canada); 001 703 527 3887 (other countries) The information and recommendations contained herein are based upon data believed to be correct; however, no guarantee or warranty of any kind expressed or implied is made with respect to the information provided.

Source: http://www.hilti.co.th/fstore/holth/techlib/docs/Hilti_HIT_HY-150MAX.pdf