Microsoft word - tds_dcon_306_e.doc

DURACON® 306
SEALER FOR DURACON® FLOORING
Shelf life
SYSTEMS IN WET PRODUCTION AREAS
6 months when stored in a cool and dry place and in originally closed packaging. The optimal storage temperature is 15 - 20°C. KEY BENEFIT SUMMARY
TECHNICAL INFORMATION

Technical characteristics (liquid state)
PRODUCT INFORMATION
Description
Technical characteristics (cured state)
Tensile strength
Duracon® 306 is a low viscosity, elastified, UV-resistant, blue- violet, 2 component reactive resin based on methyl methacry- late (MMA). After polymerisation the blue-violet colouring is no Duracon® 306 elastified surface sealer is designed for use, Please note that an objective comparison with other data is only possible if norms and parameters are identical. alone or in combination with Duracon® 301. Duracon® 305, on floor coverings exposed to surface tension from warm USAGE GUIDELINES
Substrate preparation
• as a first sealcoat on Duracon® system SL with colour flakes, followed by a second sealcoat Duracon® 301 The Duracon® coating system to be sealed must be dry, clean, free of dust and fat. Any fresh Duracon® coating as a first sealcoat on Duracon® braodcast system BC and L followed by a harder and stronger sealcoat type Dura- system must be completely cured and cooled down. As a general principle all Duracon® coating systems can be re- sealed with the same Duracon® sealer without any difficulty. as a sealcoat for floors exposed to heavy water loads For further details, see our „General Preparation and application guidelines for Duracon® floor protection sys- as a sealcoat for flexible systems for outdoor application Important advice
Duracon® 306 does not tend to heavy white discoloration as it is typical for sealers based on methyl methacrylate. Neverthe- less it is always recommended to gather waste or flowing water (particularly hot water) into channels and convey it into a proper drainage system. Provide for a sufficient number of gullies. The service durability of the floor can as a result be
Packaging
180 kg steel drum, 50 kg metal pail
DURACON® 306
HEALTH AND SAFETY PRECAUTIONS
Prior to use Duracon® 306 must be carefully stirred to Suitable protective clothing, gloves and safety goggles achieve a uniform distribution of the paraffin contained in must be worn during mixing and application of Duracon® the product. Duracon® 306 is thoroughly mixed together with the Duracon® CATALYST (50% dibenzoyl peroxyde), In case of contact with eyes rinse immediately for a long in accordance with the below guidelines. period of time and consult a physician. In case of contact It should be noted that the amount of catalyst powder to with skin clean immediately with water and soap. Duracon® 306 is highly flammable; keep away from heat and all sources of ignition and do not smoke. The stirrer as well as all the other electric appliances used on the application site must be explosion-proof versions. For further information see our Material Safety Data TECHNICAL SERVICE
Contact RPM/Belgium N.V. / Alteco Technik GmbH. Please contact our Technical Service Department for GUARANTEE
RPM/Belgium N.V. and Alteco Technik GmbH warrant all Note: Weight to Volumetric conversion of Catalyst. goods to be free from defects and will replace materials 1 cm³ of Duracon® CATALYST weighs 0.64 g The information and recommendations herein are be- lieved by RPM/Belgium N.V. and Alteco Technik GmbH to A compatible pigment powder can be used to colour the Duracon® 306. Please contact our Technical Service De-
partment for details.
Application
Immediately after the catalyst has been stirred in, the
sealer is poured onto the floor in stripes (do not apply
directly out of the mixing pails) and distributed onto the
coating with a short-pile paint roller. On sanded coatings
the sealing can be pre-spread before rolling with a
notched rubber squeegee. To avoid any possible forma-
tion of microbubbles in the sealer surface it is important to
work with freshly mixed material, i.e. to catalyze smaller
batches. Material shall be spread and rolled immediately
to an even layer thickness of not more than 400 microns.
If a thicker layer is required it must be applied in two sepa-
rate coats.
Consumption of Duracon® 306 sealer is between 0.3 and
0.6 kg/m² depending on the density and roughness of the
Duracon® coating system onto which it is applied. For
further details see our „General Preparation and applica-
tion guidelines for Duracon® floor protection systems“.

Source: http://www.simplex.co.at/en/_intern/sites/editor/bibliothek/tds_dcon_306_e.pdf

Http://cristianaarcangeli.com.br/saude-e-nutricao/com-veto-de-emagrecedores-sobram-poucos-tratamentos-contra-obesidade/

A Anvisa (Agência Nacional de Vigilância Sanitária) anunciou na semana passada que quer proibir a venda e o consumo de sibutramina e medicações derivadas de anfetamina, substâncias inibidoras de apetite, que são usadas para auxiliar no emagrecimento. Essa semana, a proposta será discutida em audiência pública e a decisão será tomada pela diretoria da agência em março. Tudo indi

Microsoft word - manuals

Fenix LD22 Flashlight The Fenix Model LD22 provides reliable illumination in a wide variety of applications. With four brightness levels and two flashing modes, LD22 employs a side mode switch for quick changes. Powered by readily-available AA batteries, this compact flashlight showcases the durability and power management for which Fenix is recognized around the world. Techni

Copyright ©2018 Drugstore Pdf Search